Full roof condition survey
We walk the entire roof, photograph every penetration and check the deck with a moisture meter. You get a written report ranking issues by urgency, so you can decide what to fix now and what can wait.
Warehouse, metal and flat roof systems done code-correct the first time
Industrial Roofing Cutler Bay FL built for storm season
When your warehouse or plant roof starts leaking, every hour of downtime costs money. Our industrial roofing Cutler Bay FL crews handle metal panels, flat membrane systems, flashing and drainage for commercial buildings across Miami-Dade County. We work around your operating hours, tarp and stop active leaks fast, and document everything for your insurer. Licensed, insured, and local to Cutler Bay, FL.
Careful work. Honest options.
About this service
Industrial Roofing Cutler Bay FL: what the work actually involves
Industrial roofing Cutler Bay FL is the commercial roofing category that covers large-footprint buildings such as warehouses, distribution centers, light-manufacturing plants and retail back-of-house structures. The work includes metal roofing panels, flat membrane and modified bitumen systems, roof flashing, drip edge, ridge vents and ice and water shield in the valleys. Crews use a roofing nail gun, pry bar, chalk line and magnetic sweeper to strip and re-secure panels, then a moisture meter to confirm the deck is dry before new underlayment goes down.
Most Cutler Bay commercial roofs fail for one of five reasons: wind uplift, ponding water on flat roofs, flashing failure at penetrations, storm damage from a named system, or fascia rot from years of salt-laden air. If you manage a building near Southland Mall Area or along the US-1 corridor, an industrial roofer in Cutler Bay can inspect the roof after every major storm and catch a small flashing failure before it becomes a five-figure interior loss. That is the whole point of scheduled industrial roof repair in Cutler Bay Florida.
- ✓ Downtime stays minimal
- ✓ Storm-ready fastening
- ✓ Leak-first triage
- ✓ Manufacturer-backed systems
What's included
What our industrial roofing service includes
Every industrial roofing project we run in Cutler Bay includes the items below as standard. Anything outside this list, like structural deck replacement or adding new HVAC curbs, gets priced separately and shown to you before we start.
Tear-off and disposal
Old membrane, panels and underlayment come off with pry bars and shingle cutters, and we haul everything away. Nails get swept with a magnetic sweeper so your parking lot and loading zones stay safe.
Code-compliant installation
New underlayment, roof flashing, drip edge and ridge vents go in to Florida Building Code and Miami-Dade County NOA standards. Fastening patterns are set for the wind-uplift zone your building sits in.
Penetration sealing
Every HVAC curb, exhaust fan, skylight and pipe boot gets sealed with compatible roof sealant and reinforced flashing. Penetrations are the number one leak source on industrial roofs, so we do not rush them.
Drainage correction
On flat roofs we check slope, clear drains and correct low spots that cause ponding water. Standing water is what kills membranes early, and fixing it now saves you a full replacement later.
Warranty and documentation
You receive manufacturer warranty registration, our workmanship coverage, and a photo set of every layer. That package is what your insurer and building inspector want to see.
How it works
How an industrial roofing project runs
We walk the roof with you, photograph every penetration, and check the deck with a moisture meter. You get a written report with the problem areas ranked by urgency. Most surveys take 60 to 90 minutes on a 20,000 sq ft building.
Within 24 hours you receive a line-item scope: square footage, system type, fastening pattern, flashing details and a fixed price. No allowances, no surprise change orders. We flag anything that is genuinely optional, like adding ridge vents while the panels are off.
Panels, underlayment, roof sealant and flashing arrive the day before work starts. We set a chalk line for panel alignment, protect your HVAC curbs, and post OSHA 10-compliant fall protection before anyone steps on the deck.
Crews strip the old system with pry bars and shingle cutters, sweep nails with a magnetic sweeper, then install new underlayment, flashing and panels. We work section by section so your operations keep moving underneath.
We water-test the repaired areas, photograph the finished roof, and hand you the warranty paperwork plus a maintenance schedule. You get a single point of contact for the life of the warranty.
STEP 01Roof survey
We walk the roof with you, photograph every penetration, and check the deck with a moisture meter. You get a written report with the problem areas ranked by urgency. Most surveys take 60 to 90 minutes on a 20,000 sq ft building.
Tools & methods
Tools and methods we bring to your roof
Moisture meter
Confirms whether the deck and insulation are wet before we install anything new. Installing over a wet deck traps moisture and guarantees an early failure.
Infrared scan
Finds hidden water in flat roof assemblies where the surface looks dry. It is how we locate leaks that are 20 feet from the interior stain.
Roofing nail gun and pry bar
Fast, consistent fastening on shingle and underlayment work, and controlled tear-off on membrane and panel removal without damaging the deck.
Chalk line and tape measure
Sets panel and membrane alignment so courses run straight and fastening patterns match the engineer's spec.
Magnetic sweeper
Sweeps nails and fasteners from your lot and loading zones before we leave. Flat tires on your forklifts are not an acceptable side effect of a roof job.
Ladder and roof harness
OSHA 10-compliant fall protection for every crew member on every pitch. No exceptions, no shortcuts.
Real results
Before and after.
Industrial Roofing
Warehouse flat roof ponding corrected
A 24,000 sq ft warehouse near Cutler Ridge had ponding water across three bays after every storm. Two prior contractors quoted full replacement. The membrane was 12 years old but the deck tested dry.
After: We cleared and resized the drains, added tapered insulation to correct the low spots, and re-sealed the seams. Ponding was gone after the next heavy rain, and the building avoided a $280,000 tear-off.
Book this service →
Industrial Roofing
Metal panel wind uplift repaired
A light-industrial building in Saga Bay lost 14 standing-seam panels during a named storm. Water was entering the racking area, and the owner's insurer wanted documentation before approving the claim.
After: We tarped the same afternoon, photographed the damage, and replaced the panels with supplemental fasteners matched to the current Miami-Dade County NOA. Claim approved in 11 days.
Book this service →
Industrial Roofing
Flashing failure stopped before interior damage
A property manager near Southland Mall Area noticed a small ceiling stain in a tenant space. The roof surface looked fine, and no one could find the source.
After: An infrared scan traced the leak to a failed HVAC curb flashing 18 feet away. We rebuilt the flashing, water-tested it, and the stain stopped spreading. Total repair cost was $1,850.
Book this service → Problems we solve
Industrial roof problems we fix in Cutler Bay
Most industrial roof failures in South Florida start small and get expensive fast. Here are the problems we see most often on Cutler Bay commercial buildings and how we handle each one.
Ask a pro →Ponding water on flat roofs after heavy rain
We survey the slope, clear and resize drains, and correct low spots with tapered insulation or a recovery board. Then we re-seal the seams and re-inspect after the first heavy rain to confirm the water is moving.
Wind uplift lifting metal panels and shingle tabs
We replace lifted panels and shingles, verify the fastening pattern against the Miami-Dade County NOA for your assembly, and add supplemental fasteners where the uplift zone demands it. Every repair is photographed.
Flashing failure at HVAC curbs and pipe boots
We cut out the failed flashing, clean the substrate, and rebuild the detail with new flashing and compatible roof sealant. We water-test the repair before closing out the work order.
Fascia rot and soffit damage from salt air
We remove rotted fascia, replace it with treated material, and reinstall the drip edge and soffit with proper ventilation. Coastal buildings near Bayshore and Coral Bay get extra attention here.
Proof you can check
Licensed, certified and accountable
- Florida Roofing License (RR) · Florida Department of Business and Professional Regulation
- GAF Master Elite · GAF
- Owens Corning Preferred Contractor · Owens Corning
- OSHA 10 · Occupational Safety and Health Administration
- NRCA Member · National Roofing Contractors Association
Typical 2026 pricing runs $8 to $16 per square foot installed, so a 20,000 sq ft warehouse lands between $160,000 and $320,000 depending on system type. Metal industrial roofing Cutler Bay projects sit at the higher end; recover-over on a sound flat deck sits lower. Repairs are far cheaper: most flashing and leak fixes run $850 to $4,500.
The best industrial roofing contractor Cutler Bay has is the one who shows you the deck condition, the fastening spec and the warranty in writing before asking for a deposit. Ask for the Florida Roofing License (RR) number, manufacturer credentials like GAF Master Elite, and Miami-Dade County NOA approvals on the assembly. We provide all three on every quote.
Yes. We handle flashing failure, wind uplift damage, punctured membrane, ponding water on flat roofs and fascia rot across Cutler Bay and Miami-Dade County. Most repairs are completed in one to two days, and we tarp active leaks the same day you call. You get photos before and after, plus a written report for your files.
A 20,000 sq ft warehouse typically takes 6 to 10 working days from tear-off to final walk. Larger buildings run two to four weeks. Weather is the main variable: October through November is our busiest storm-season window, so scheduling ahead of hurricane season gets you on the calendar faster.
Ready when you are
Get your industrial roofing Cutler Bay FL quote today
We answer the phone, show up when we say we will, and put the scope in writing before any work starts. Licensed, insured and local to Cutler Bay, FL. Call (855) 960-5906 and we will schedule your roof survey this week.
Request a roof survey (855) 960-5906 →
Request an appointment
Contact our Cutler Bay roofers
Call (855) 960-5906 or email [email protected] and we will get you on the schedule. We answer 24/7 for emergencies and book standard inspections within 24 hours. If you are in ZIP codes 33190, 33157, or 33189, we are already in your area.
Call anytime(855) 960-5906Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week