Full tear-off and disposal
We strip the old roof down to the plywood, load it into a dumpster, and haul it away. On average that is 22 to 30 squares of debris per home. We tarp your landscaping before the first shingle comes off.
Licensed, insured, and code-correct crews serving Miami-Dade County
Roof Installation Cutler Bay FL built to survive storm season
When you need roof installation Cutler Bay FL homeowners can count on, our crew tears off the old decking, replaces rotten fascia, and sets a new roof system engineered for wind uplift and summer downpours. We handle asphalt shingles, metal panels, and tile, pull the Miami-Dade County NOA paperwork, and leave your yard swept clean. Most homes are dried in within two days, weather permitting.
Careful work. Honest options.
About this service
What roof installation Cutler Bay FL really involves
Roof installation Cutler Bay FL means removing the existing covering down to the deck, inspecting every sheet of plywood, and rebuilding the roof system from the underlayment up. We install ice and water shield along the valleys and eaves, lay synthetic roofing felt across the field, then set drip edge, roof flashing, and ridge vents before a single shingle goes down. On a typical 1,800-square-foot ranch home, that is roughly 22 squares of material and about 60 fasteners per square.
Cutler Bay sits in a high-velocity hurricane zone, so your roof takes salt air off Biscayne Bay, 90-plus-degree surface temperatures from May through September, and afternoon thunderstorms that dump two inches of rain in under an hour. If your shingles are curling, your flashing is lifting, or you are seeing granules in the gutter, you are looking at a new roof installation Cutler Bay sooner than later. We also handle roof installation for new construction Cutler Bay, working directly from your plans and inspection schedule.
- ✓ Storm-rated wind protection
- ✓ Lower cooling bills
- ✓ Leak-free for decades
- ✓ Curb appeal and resale
What's included
What our roof installation covers
Every roof installation we do is a full system replacement, not a layover. That means tear-off to the deck, new underlayment, new flashing, and new ventilation. Here is what is in the standard scope, and what we price separately if your home needs it.
Decking inspection and repair
Every sheet of plywood gets walked and probed. Rotten or delaminated decking gets replaced and re-nailed to the Florida Building Code pattern. We photograph anything we replace so you see exactly what was wrong.
Underlayment and flashing
Ice and water shield goes at every valley, eave, and penetration. Synthetic felt covers the field. New drip edge, roof flashing, and pipe boots go on before the finished roofing. This is the layer that actually keeps water out.
Ventilation and ridge vents
We install ridge vents matched to your roof profile and confirm your soffit intake is clear. Proper intake and exhaust is what keeps attic temperatures down and stops moisture from cooking your decking from underneath.
Permit and inspection
We pull the Miami-Dade County roofing permit, file the NOA product approvals, and meet the inspector on site. You do not chase paperwork or take a day off work for the inspection.
Final cleanup and warranty
Magnetic sweep of the lawn and driveway, gutter blowout, and dumpster removal. Then we walk the roof with you, hand over the manufacturer and workmanship warranty documents, and leave the material spec sheet for your records.
How it works
How our roof installation process runs
We walk the roof, check the attic decking from underneath, and photograph every problem area. You get a written scope with square counts, material options, and a fixed price. Most inspections take 45 minutes and you get the estimate the same day.
Once you approve the scope, we order your shingles, underlayment, and flashing from our supplier. GAF and Owens Corning products usually land at the job site within 48 hours. We schedule your install date around the delivery so nothing sits on your lawn overnight.
The crew arrives at 7 a.m. with a dumpster and tarp protection over your landscaping. We strip the old roof, replace any rotten fascia or soffit damage, and re-nail loose decking. Tear-off on an average home takes one full day.
We lay ice and water shield, felt, drip edge, and flashing, then set the field shingles or panels. Ridge vents and pipe boots go on last. A standard shingle roof is watertight by end of day two; tile and metal run three to four days.
We run a magnetic sweeper across the lawn and driveway twice, blow out the gutters, and haul the dumpster. Then we walk the finished roof with you, hand over the warranty paperwork, and photograph the install for your records.
STEP 01Free inspection
We walk the roof, check the attic decking from underneath, and photograph every problem area. You get a written scope with square counts, material options, and a fixed price. Most inspections take 45 minutes and you get the estimate the same day.
Tools & methods
Tools and methods we bring to your roof
Roofing nail gun
Sets shingle fasteners at the correct depth and angle. We run pneumatic guns set to the Florida Building Code nailing pattern so every tab gets the right number of fasteners.
Shingle cutter
Cuts clean edges at hips, ridges, and valleys without tearing the mat. Clean cuts mean fewer exposed edges where wind can grab.
Ladder and roof harness
OSHA-compliant fall protection on every pitch. Our crews are tied off from the moment they step onto the roof until they step back down.
Moisture meter
Reads decking moisture from the attic side. It tells us whether a soft spot is surface rot or a full sheet that needs replacing before we install over it.
Magnetic sweeper
Picks up dropped nails and staples from the lawn and driveway. We run it twice before we leave, which is why you will not find nails in your grass next month.
Leaf blower
Clears granules and debris from gutters and walkways at the end of the job. It is the last thing we do before the final walk-through with you.
Real results
Before and after.
Roof Installation
Saga Bay shingle roof after storm loss
A 2003 shingle roof lost 14 tabs along the ridge and both valleys during a summer squall. The homeowner had two active ceiling leaks and a bucket in the hallway. The decking under the ridge was soft and the pipe boots were cracked.
After: We tore off 24 squares, replaced four sheets of decking, and installed a new GAF Timberline system with ice and water shield at both valleys. The roof was dried in on day two and passed inspection on the first visit.
Book this service →
Roof Installation
Cutler Ridge tile underlayment replacement
A 1978 concrete-tile roof had original underlayment that crumbled when we lifted the first tile. Three separate leaks had stained the ceiling in two bedrooms. The homeowner assumed the whole tile roof had to go.
After: We lifted and stacked the tile, replaced 30 squares of underlayment and flashing, and reset 95 percent of the original tile. The job cost roughly half of a full tile replacement and the leaks stopped.
Book this service →
Roof Installation
Southland Mall Area flat roof ponding fix
A 6,000-square-foot commercial flat roof held standing water in two low spots after every rain. Seams were separating and algae had taken over the surface. The tenant below had a recurring ceiling stain.
After: We added tapered insulation to redirect drainage, replaced the failed seams, and recoated the membrane. The ponding cleared within one rain cycle and the interior stain stopped growing.
Book this service → Problems we solve
Roof problems we fix before they spread
Most roof failures start small and stay invisible until the ceiling stains. Here are the four we see most often in Cutler Bay, and what happens if you wait.
Ask a pro →Missing shingles after a wind event
We match your shingle profile and color, replace the missing tabs, and reseal the surrounding field. If the loss is widespread, we document it for an insurance claim and quote a full roof installation instead of chasing patches.
Flashing failure at walls and chimneys
We remove the old flashing, install new metal flashing with proper laps, and seal it with roofing-grade sealant. Then we hose-test the area before closing it up so we know the leak is actually gone.
Ponding water on flat roofs
We locate the low spots, add tapered insulation or a new drainage path, and reseal the membrane. On older flat roofs we recommend a full replacement with a properly sloped system.
Fascia and soffit rot from overflow
We replace the rotted fascia and soffit during the roof installation, then re-hang the gutter with new hangers. Fixing it while the roof is open costs a fraction of coming back later.
Proof you can check
Licensed, insured, and documented
- Florida Roofing License (RR) · Florida Department of Business and Professional Regulation
- GAF Master Elite · GAF
- Owens Corning Preferred Contractor · Owens Corning
- OSHA 10 · Occupational Safety and Health Administration
- NRCA member · National Roofing Contractors Association
Most asphalt shingle roofs in Cutler Bay run $12,000 to $22,000 in 2026, depending on square footage and pitch. Tile and standing-seam metal typically land between $24,000 and $45,000. Steep two-story roofs, rotten decking, and multiple layers of tear-off push the number up. We give you a fixed written price after the inspection, so you know the total before we start.
A standard shingle roof on a single-story home is torn off and watertight in two days. Tile and metal systems run three to four days because of the heavier material and extra fastening. Rain delays in summer are the only thing that slows us down. We watch the radar and schedule around afternoon storms so your roof is never left open overnight.
Elyndor Forge Group installs new roofs across Cutler Bay and the rest of Miami-Dade County. We are a licensed Florida Roofing contractor, insured and bonded, and we have been working South Florida roofs since 2021. Our crews handle asphalt shingles, metal panels, clay and concrete tile, and flat roof systems. Call (855) 960-5906 and we will set an inspection.
Yes. We pull the Miami-Dade County roofing permit and schedule the inspection as part of the job. Your price includes the permit fee and the inspection coordination, so you are not chasing paperwork. We also file the Miami-Dade County NOA product approvals with the permit so your final inspection clears without a second visit.
Ready when you are
Get your roof installation Cutler Bay FL quote today
Call (855) 960-5906 and we will inspect your roof, photograph the problem areas, and hand you a fixed written price the same day. Licensed, insured, and working Cutler Bay since 2021.
Schedule Free Inspection (855) 960-5906 →
Request an appointment
Contact our Cutler Bay roofers
Call (855) 960-5906 or email [email protected] and we will get you on the schedule. We answer 24/7 for emergencies and book standard inspections within 24 hours. If you are in ZIP codes 33190, 33157, or 33189, we are already in your area.
Call anytime(855) 960-5906Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week